My Vehicle
Cart
Will a myCOOLMAN Fridge Fit in My Ute? How to Measure Before You Buy "Will it fit?" is the question we get asked most about portable fridges. Will it fit in the tub, under the roll...
Read article"Will it fit?" is the question we get asked most about portable fridges. Will it fit in the tub, under the roller cover, behind the seat, in the drawer system or in the caravan? Getting it wrong is a pain, so here is how to measure your space properly, plus the external dimensions of every myCOOLMAN fridge we sell.
Grab a tape measure and check the actual space the fridge will sit in. Every ute, canopy and drawer system is a little different, and factory figures rarely allow for tub liners, wheel arches, tie-down points or the roller cover canister.
The table below lists the external size of every myCOOLMAN chest fridge in our range, sorted by height, as height is usually the deciding measurement under a roller cover or canopy. All sizes are in millimetres.
| Fridge | Height (mm) | Length (mm) | Width (mm) | Weight |
|---|---|---|---|---|
| myCOOLMAN Recreational 20 | 368 | 452 | 346 | 10kg |
| myCOOLMAN Recreational 38 Dual Zone | 460 | 648 (incl. handles) | 401 | 17.5kg |
| myCOOLMAN Recreational 43 | 460 | 648 (incl. handles) | 401 | 16.5kg |
| myCOOLMAN Premium 53 Dual Zone | 460 | 732 | 456 | 27.8kg |
| myCOOLMAN Recreational 55 Dual Zone | 460 | 762 (incl. handles) | 461 | 20.8kg |
| myCOOLMAN Recreational 60 | 460 | 762 (incl. handles) | 461 | 18.9kg |
| myCOOLMAN Recreational 78 Dual Zone | 460 | 901 (incl. handles) | 502 | 26.3kg |
| myCOOLMAN Premium 85 Dual Zone | 470 | 912 | 536 | 33.6kg |
| myCOOLMAN Premium 44 | 488 | 652 | 412 | 23.4kg |
| myCOOLMAN Premium 60 | 488 | 732 | 456 | 25.6kg |
| myCOOLMAN Premium 96 Dual Zone | 500 | 912 | 536 | 34.9kg |
| myCOOLMAN Premium 105 | 500 | 912 | 536 | 33.2kg |
| myCOOLMAN Premium 69 Dual Zone | 555 | 732 | 456 | 29.4kg |
All five Recreational Series fridges from 38L to 78L are 460mm high, so under a tight roller cover you can often go bigger in length without losing height.
Upright fridges open from the front, so they suit spaces where you cannot lift a lid, such as a canopy, camper trailer kitchen or caravan cabinet. Measure the cabinet or cut-out, and allow room for the door to swing open and for ventilation.
| Fridge | Height (mm) | Width (mm) | Depth (mm) | Weight |
|---|---|---|---|---|
| myCOOLMAN Upright 80 Dual Zone | 625 | 475 | 560 | 23.8kg |
| myCOOLMAN Upright 115 Dual Zone | 752 | 520 | 560 | 28.6kg |
| myCOOLMAN Upright 205 Dual Zone | 1437 | 520 | 680 | 56.6kg |
A full fridge is far heavier than the empty weights above. Add the weight of food and drinks, check your tub, drawer or slide's load rating, and use proper tie-downs so the fridge cannot move on corrugations or under hard braking.
Still not sure? Send us your measurements and vehicle details and we will help you find a myCOOLMAN fridge that fits. Just contact our team.
Starlink Mini Cases: Your Options and Why You Need One Most people do not think about a case until they have unboxed their Starlink Mini . Then they find out the hard way that it w...
Read articleMost people do not think about a case until they have unboxed their Starlink Mini. Then they find out the hard way that it will not go back into its original box.
The Starlink Mini Travel Soft Case is a padded case with custom-shaped compartments for the Mini, its kickstand and power supply. At 1.2kg and 329 x 296 x 166mm, it slips into a backpack, drawer or behind the seat, with a handle for easy carrying.
Best for: carrying the Mini inside the vehicle, day trips, hiking and anyone who wants the lightest option.
The Hard Travel Case for Starlink Mini has an impact-resistant shell, a custom-cut foam insert that holds the Mini firm, and a latching lid that keeps dust and knocks out.
Best for: ute trays, drawer systems, corrugated outback roads, flights and anyone who packs heavy gear around the dish.
If you are still setting up, our Travel Bundle combines a travel case with a 12V to 30V booster and a 5m DC cable. The Touring Bundle adds a magnetic roof mount as well.
| Soft Case | Hard Case | |
|---|---|---|
| Protection | Padded | Impact-resistant shell with foam insert |
| Weight | 1.2kg | Heavier, built for protection |
| Holds | Mini, kickstand and power supply | Mini in a custom-cut foam insert |
| Best for | Inside the vehicle, backpacks | Ute trays, drawers, corrugations, flights |
If the Mini rides in the cabin or a backpack, the soft case is all you need. If it travels in a ute tray, drawer system or on rough roads, go the hard case.
Questions about which case suits your setup? contact our team.
Why Do I Need a 30V Booster for My Starlink, and Which Model Do I Need? The Starlink Mini runs on 12–48V DC, so on paper you can plug it straight into a 12V battery. In practice, m...
Read articleThe Starlink Mini runs on 12–48V DC, so on paper you can plug it straight into a 12V battery. In practice, many people running it off 12V find it drops out or reboots, usually at the worst time. A 12V to 30V booster fixes that.
12V sits right at the bottom of the Mini's input range, with very little room to spare. Three things eat into that margin:
Add those together and the voltage at the dish can fall below what it needs. The result is a dropout or a restart.
A step-up booster takes your 12V supply and turns it into a steady, regulated 30V, even when the battery sags. At 30V the Mini draws less than half the current it would at 12V for the same power, so there is far less voltage lost in the cable. The result is a stable connection that stays up.
All of our boosters are made for the Starlink Mini. The right one depends on how you connect to your 12V system.
| Your setup | Booster | Why |
|---|---|---|
| Battery box, DC-DC system or Anderson outlet | 12V to 30V Booster, Anderson Plug | Anderson input with inline fuse, IP67 sealed, 1m output lead |
| Cigarette or accessory socket in a car, ute or caravan | 12V to 30V Booster, Cigarette Plug | Plug in and go, no wiring. 10A fused plug, 90W output |
| Our lockable or aluminium roof rack mount | 12V to 30V Booster for Roof Rack Mounts | Short 30cm leads so it sits inside the lockable mount or aluminium bracket |
| A built-in outlet in a caravan, motorhome or canopy | Waterproof Boosted Power Outlet | Booster built into a panel socket. 12V or 24V in, 30V out, IP67 with the cap on |
Our plug-in boosters take a 12V input (9–15V), so do not plug them into a 24V system. A 24V truck or bus already sits comfortably in the Mini's range, so you can usually run it directly with a 12/24V cigarette lead. For a fixed outlet, the Boosted Power Outlet takes 12V or 24V.
Run the Mini from the 18V tool batteries you already own with our Milwaukee, Makita, DeWalt or Ryobi battery adaptors. Or use a 100W USB-C PD source such as our 130W USB-C car charger with a USB-C to DC cable made for the Mini.
The Anderson and cigarette boosters have an output socket that takes the Mini's DC cable. Use the factory 15m cable, or swap to a 3m, 5m or 10m cable for a neater install. Our Travel Bundle and Touring Bundle include a booster and 5m cable together.
If you run your Mini off 12V, fit a booster. For most caravans and 4WDs with a battery box, the Anderson booster is the one to get. If you only have a cigarette socket, go the cigarette plug booster. Mounting on the roof rack? The roof rack booster is made to fit inside our mounts.
Not sure what your setup needs? contact our team and we will check it with you.
How to Pick the Best Set of Driving Lights A good set of driving lights changes night driving. You see roos, cattle and potholes sooner, you are less tired at the end of a long run...
Read articleA good set of driving lights changes night driving. You see roos, cattle and potholes sooner, you are less tired at the end of a long run, and you can drive the outback at night with far more confidence. But with so many lights on the market, the specs can be hard to compare.
Here is what actually matters, and how to match a light to the way you drive.
The most useful number on a driving light is the 1 lux distance: how far down the road the beam still gives 1 lux of light, about the brightness of a full moon. The further it is, the more warning you get of what is ahead.
Lumens tell you how much light comes out of the light in total, but not where it goes. Two lights with similar lumens can throw very differently depending on their reflectors. Also check whether a figure is quoted per light or per pair, as brands mix both.
Many people pair a long-range set of driving lights with a light bar for spread. If you only fit one set, a combination beam is the safe choice.
Most LED driving lights sit between 5,000K and 6,500K, which is close to daylight. Around 5,700K is a good balance of brightness and contrast. Very blue light can cause more glare off road signs and in dust or rain.
Look for an IP68 or IP69K rating, which means the light is sealed against dust and water. Then look at the details that matter on corrugations: an aluminium housing that draws heat away from the LEDs, a polycarbonate lens that will not shatter from a stone, and a solid stainless steel bracket that will not crack or rust.
If you run a 24V truck or bus, make sure the light runs on 24V. All of the lights below run on both 12V and 24V systems.
| Light | Beam | 1 lux distance | Best for |
|---|---|---|---|
| Apex 8.5 | Long range | About 1,780m | Maximum reach on long outback runs |
| Apex 7 | Long range (hyper spot) | 1,480m | Long reach in a smaller light |
| Apex 180 | Ultra wide (hyper flood) | 874m | Winding tracks, wildlife, worksites |
| Apex Quad | Combination, with daytime running lights | Not published | A sleek square look with DRLs |
| Adventure Series 9 | Combination | 810m | Strong all-rounder on a budget |
| Adventure Series 7 | Combination | 468m | Entry level upgrade for town and touring |
The Apex range is our premium line, built with Osram LEDs, precision reflectors and heavy-duty stainless steel brackets with three-point mounting. The Apex 8.5 is the long-range leader. The Apex 7 packs similar reach into a smaller housing. The Apex 180 trades some distance for a very wide beam that lights up the whole road edge, and the Apex Quad adds daytime running lights in a square design. The Apex 7 is rated IP69K and the Apex Quad IP68.
The Adventure Series 7 and Adventure Series 9 are our entry-level lights, with an aluminium housing, oversized heatsink, unbreakable polycarbonate lens and IP68 rating. A big step up from factory high beams without the premium price.
Driving lights must only work with your high beams, so they switch off when you dip for oncoming traffic. Check your state's rules for fitting and mounting height too.
Protect your investment with anti-theft security lock nuts, and add day covers to shield the lenses from stones and scrub during the day.
For long outback runs at highway speed, go the Apex 8.5 or Apex 7. For tight tracks and wildlife country, the Apex 180. For a first set of driving lights on a budget, the Adventure Series 9. Pair any of them with the right harness for your vehicle.
Need help choosing, or not sure which harness fits your vehicle? contact our team.
How to Pick the Best Starlink Mini Mount The kickstand that comes with the Starlink Mini is fine for a quick setup at camp, but it is not much help on a car roof, under trees or on...
Read articleThe kickstand that comes with the Starlink Mini is fine for a quick setup at camp, but it is not much help on a car roof, under trees or on a windy day. A proper mount puts the dish where it gets a clear view of the sky, keeps it steady, and saves you setting it up every time you stop.
There is no single best mount. The right one depends on your vehicle, how long you stay in one spot and whether you leave the dish fitted. Here is how to work it out.
If you have a roof rack, a rack mount is the most secure and tidy option. The dish sits up high with a clear view, the cable can be run neatly, and it is ready to go when you pull up.
Tip: both the lockable mount and the aluminium bracket have room inside for our roof rack 30V booster. Run one Anderson cable up to the roof and the booster sits out of sight in the mount, with short leads and nothing to snag.
The Magnetic Flat Mounting Bracket Kit uses four magnets, each rated to about 45kg of pull, to hold the Mini flat on a steel roof. No drilling and no tools, and it comes off in seconds. It suits travellers who move every day and want to set up in seconds when they stop.
It needs a flat steel surface, so it will not work on aluminium or fibreglass roofs, most caravans or canopies. Wipe the roof and magnets clean before you fit it so grit does not scratch the paint.
The Suction Cup Mount uses four lever-lock cups to hold the Mini on a windscreen, sunroof or any smooth, non-porous panel. It is the most flexible and lowest cost option, and it is made from heat-resistant ABS to cope with hot Aussie cars. Great for hire cars, work vehicles and anyone who does not want to change their vehicle at all.
Fit it to clean, dry glass, and check the cups before each use.
| Mount | Fits | Best for | Lockable |
|---|---|---|---|
| Slimline Lockable | Roof racks, canopies, caravans | Long trips, leaving it fitted | Yes |
| Aluminium Bracket | Roof racks, canopies, caravans | Permanent touring setups | No |
| Roof Rack Clamp | Rack bars 12–48mm | Compact rack setups | No |
| Magnetic | Flat steel roofs | Moving camp every day | No |
| Suction Cup | Glass, smooth panels | Temporary and hire vehicles | No |
The Mini comes with a 15m DC cable, which leaves metres to coil up once the dish is on the roof. A 3m, 5m or 10m DC cable makes for a much tidier install. On a 12V system, add a 30V booster to keep the connection stable. We explain why in Why do I need a 30V booster for my Starlink?
If you have a roof rack and tour for weeks at a time, go the lockable mount with the roof rack booster inside it. If you move every day in a vehicle with a steel roof, the magnetic kit is hard to beat. For the occasional trip or a hire car, the suction cup mount does the job for the least money.
Not sure which suits your vehicle? contact our team and we will help you work it out.
Every 12V setup needs the right plugs and sockets. Pick the wrong one and your fridge drops out on corrugations, or your coffee machine blows a fuse. This guide explains the commo...
Read articleEvery 12V setup needs the right plugs and sockets. Pick the wrong one and your fridge drops out on corrugations, or your coffee machine blows a fuse. This guide explains the common 12V connectors, what each one is good for, and how to choose cable and fuses.
The short answer: use a 50A Anderson-style plug for high-current gear like fridges, solar, battery boxes and appliances. Use a cigarette or Merit socket for small accessories up to about 10A, and a USB-C PD socket for phones and tablets.
| Connector | Typical rating | Best for | Watch out for |
|---|---|---|---|
| 50A Anderson-style plug | 50A | Fridges, solar, battery boxes, DC-DC chargers, 12V appliances | Grey and red housings will not join |
| Cigarette socket | Usually about 10A | Pumps, inflators, chargers, small fridges | Plugs can work loose on rough roads |
| Merit (Hella) socket | 10A | Fridges and European-style plugs | Smaller than a cigarette socket |
| USB-C PD socket | Up to 45W (our TVDSU3) | Phones, tablets, cameras | Needs a PD-capable device for full speed |
| QC 3.0 USB-A socket | 18W per port | Android phones, GPS, headlamps | Slower than USB-C PD for laptops |
| Your gear | Typical draw | Use |
|---|---|---|
| 12V fridge | 1 to 5A, more on start-up | Anderson for a secure fit, or a Merit/cigarette plug for light use |
| 12V coffee machine or air fryer | 20 to 30A | Anderson only |
| Solar panel or blanket | Up to the panel's rating | Anderson |
| Phone, tablet or camera | Under 5A | USB-C PD or QC 3.0 socket |
| Tyre inflator | 10 to 30A | Anderson or battery clamps for bigger ones |
Draw figures are typical and vary by model. Check the rating of the product you use.
Mounting sockets in a canopy, drawer or caravan? Read flush mount vs surface mount Anderson sockets.
An Anderson-style plug is a heavy-duty, genderless 12V connector. The common 50A size is used for fridges, solar panels, battery boxes, DC-DC chargers and caravan connections.
They are the same plug in different colours, but the housings are keyed so a grey and a red plug will not join. Use matching colours, or a grey to red adapter lead.
A Merit (Hella) socket is the smaller European-style 12V socket. A cigarette socket is the larger common car socket. Many 12V fridges come with a combined plug that fits both. Both are usually rated around 10A.
Use Anderson for anything that draws more than about 10A, such as a coffee machine, air fryer or compressor, and for fridges where a loose cigarette plug can drop out on rough roads.
Size the cable for the current and the length of the run, and fit a fuse that protects that cable. Our 50A Anderson leads use 8 B&S (8 AWG) cable.
Yes. A USB-C PD socket charges modern iPhones, Samsungs and Pixels at full speed. Our TVDSU3 has a 45W USB-C PD port and an 18W QC 3.0 USB-A port, and fits a standard 29.2mm hole.
The Starlink Mini runs on DC power, which makes it a natural fit for a 4WD, caravan or boat. There are several ways to power it from 12V, and the right one depends on what you plu...
Read articleThe Starlink Mini runs on DC power, which makes it a natural fit for a 4WD, caravan or boat. There are several ways to power it from 12V, and the right one depends on what you plug into. This guide compares every option, how much battery the Starlink Mini uses, and how to stop dropouts.
The short answer: the Starlink Mini accepts 12 to 48V DC and averages about 25 to 40W. You can run it from a cigarette socket, an Anderson outlet, USB-C PD or an 18V tool battery. On a 12V system, a 12V to 30V booster is the most reliable choice because it stops the dropouts caused by low voltage.
| Your power source | What to use | Good to know |
|---|---|---|
| Anderson outlet or battery box | 12V to 30V booster, Anderson plug | Most reliable 12V setup, inline fuse, IP67 |
| Cigarette or accessory socket | 12V to 30V booster, cigarette plug | Plug in and go, 10A fused plug |
| Built-in caravan or canopy outlet | Waterproof boosted power outlet | 12V or 24V in, 30V out, panel mount |
| USB-C PD power bank or charger | USB-C to DC cable | Needs 20V PD at 65W or more |
| Several sources, one lead | 3 in 1 power lead | USB-C, cigarette and DC5521 plugs on one cable |
| 18V power tool battery | 18V battery adaptor | No 12V system needed, about 2 hours on 5Ah |
| 24V truck or bus | 12/24V cigarette lead | No booster needed, 24V is within range |
A 12V battery reads above 12V when charged, but it falls as it drains and dips further when a fridge or inverter kicks in. Long cables lose more voltage, and the Starlink Mini draws extra power while it starts up. Together these can pull the voltage at the dish below what it needs. A booster turns your 12V into a steady 30V, so the Starlink Mini draws less current and loses less in the cable. Read more in why you need a 30V booster.
| Use | Approx. energy | From a 12V battery |
|---|---|---|
| 1 hour | 25 to 40Wh | About 2 to 4Ah |
| 8 hours (a working day) | 200 to 320Wh | About 17 to 30Ah |
| 24 hours | 600 to 960Wh | About 50 to 90Ah |
Figures are approximate and include a little for conversion losses. Use rises with heating in cold weather and while the dish searches for satellites.
Want it all in one box? The Starlink Mini Travel Bundle includes a booster and cable. Not sure what suits your setup? Ask our team.
Yes, the Starlink Mini accepts 12 to 48V DC. But 12V sits at the bottom of that range, so battery sag, cable voltage drop and start-up peaks can make the Starlink Mini drop out. A 12V to 30V booster gives it a steady supply.
The Starlink Mini averages about 25 to 40W, and draws more while it starts up and finds satellites.
At 25 to 40W, a Starlink Mini uses roughly 2 to 4Ah an hour from a 12V battery, or about 50 to 90Ah over a full day. A 100Ah lithium battery runs it for most of a day before other loads are counted.
Yes, with a USB-C to DC cable made for the Starlink Mini and a USB PD source that supplies 20V at 65W or more. Our 130W car charger has a 100W PD port that suits it.
Usually not. 24V sits comfortably within the Starlink Mini's range, so a 12/24V cigarette lead normally works. Our plug-in boosters are 12V input only, so never plug them into 24V.
Yes. Our 18V adaptors for Milwaukee, Makita, DeWalt and Ryobi batteries run the Starlink Mini with no 12V system. A 5Ah battery gives about 2 hours.
A 12V electric blanket is the simplest way to stay warm in a car, swag, camper or boat. It plugs into a cigarette socket and draws only a few amps. This guide covers how much powe...
Read articleA 12V electric blanket is the simplest way to stay warm in a car, swag, camper or boat. It plugs into a cigarette socket and draws only a few amps. This guide covers how much power one uses, how long it will run on your battery, and how it compares with a heater.
The short answer: a 12V electric blanket like ours draws about 50W (4.2A), so it uses roughly 4Ah of battery an hour. That is the most battery-friendly way to keep warm off-grid, because it heats you rather than the air.
| Option | Draw at 12V | Warms | Best for |
|---|---|---|---|
| 12V electric blanket | About 4.2A (50W) | You | Cars, swags, campers, boats |
| Diesel heater | 1 to 2A once running, plus diesel | The whole van | Caravans and vans in cold weather |
| 240V blanket through an inverter | About 5 to 10A including inverter losses | You | Only if you already own one |
| 240V heater through an inverter | Over 100A | The room | Not practical off-grid |
Figures are typical. Check the rating of the product you use.
| Battery (usable) | Run time at 50W (approx.) |
|---|---|
| 50Ah | About 10 hours |
| 100Ah | About 20 hours |
| 200Ah | About 40 hours |
Most people only run a blanket for an hour or two, so it uses a small share of a camping battery.
Want to warm the whole van too? Read our 12V heater guide.
Ours is rated at 50W, about 4.2A at 12V. That is roughly 4Ah of battery for every hour it runs.
In theory around 20 hours on a 100Ah lithium battery at 50W. In practice you only need it for an hour or two to warm up, so it barely dents a camping battery.
Yes. It plugs into the cigarette or accessory socket. With the engine off, keep use short so you do not flatten the starting battery, or run it from an auxiliary battery or power station.
Use it to warm up, then switch it off and unplug it before you go to sleep.
A blanket warms you for about 4A. A diesel heater warms the whole van for 1 to 2A once running, but costs more and needs installing. Many people use a blanket in bed and a heater for the evening.
You can, but the inverter wastes power and adds another device to run. A 12V blanket plugs straight into your socket.